0.5 in. Key Hub

am-0976

$9.00

This is the "500EX Key Hub". It is a slightly different version of the 500 Key Hub. It is manufactured differently, as it is extruded. Also, there is a 1.124 in. diameter boss on each side of the h...Read More

View Full Details

Product Overview

This is the "500EX Key Hub". It is a slightly different version of the 500 Key Hub. It is manufactured differently, as it is extruded. Also, there is a 1.124 in. diameter boss on each side of the hub flange, providing a location for 1.125 in. bore flat sprockets. Are you having a hard time keeping your sprocket concentric with your hub? This hub is the trick.

The bore is a 1/2 in. hole with two 1/8 in. keyways. Only one keyway is needed to drive most wheels, so the second one is extra.

Also, the keyways are consistently aligned with the mounting holes.

Specifications

  • Bolt Pattern: 0.204 in. diameter holes on a 1.875 in. bolt circle
  • Bore: 0.502 - 0.508 in. diameter bore
  • Material: 6063 Aluminum
  • Outside Diameter: 2.25 in.
  • Weight: 0.3 lbs

Documents

Layout Print(s)
CAD File(s)
Don't see what you need?

Returns

Returns are not accepted for this product.

14 reviews

  1. star star star star star 5 out of 5 stars

    Review

    5 Stars

    AW from Providence

  2. star star star star star 5 out of 5 stars

    Review

    5 Stars

    RH from Oxford

  3. star star star star star 5 out of 5 stars

    Review

    5 Stars

    RR from Russiaville

  4. star star star star star 5 out of 5 stars

    Key Hub

    This is a must have for any FIRST team. We use these for rapid prototyping as well as competition.

    RC from Mount Vernon

  5. star star star star empty_star 4 out of 5 stars

    Review

    4 Stars

    TO from Maumee

  6. star star star star star 5 out of 5 stars

    Review

    5 Stars

    RZ from Youngstown

  7. star star star star star 5 out of 5 stars

    Review

    5 Stars

    RA from Holland

  8. star star star star star 5 out of 5 stars

    Review

    Boss helps center sprockets on hub.

    DR from DALLAS

  9. star empty_star empty_star empty_star empty_star 1 out of 5 stars

    3 of 4 good. 1 unusable

    3 of 4 ordered were great. Had to order a replacement for one because key ways we're cut improperly. Replacement part had same problem. Ended up boring them out and using collars instead of original design.

    TS from Somerville

  10. star star empty_star empty_star empty_star 2 out of 5 stars

    500EX Ket HUb

    To Whom ot may Concern, The quality of these Hubs were fine but the shipping cost was too high. Overall I am not happy with Andy Mark's quality. The Gearboxes we odered did not ave the correct sprocket size. The Keyed Shafts were oversized and we had to machine them down. The Engineering specifications for product are not always clear.

    NC from San Jose

  11. star star star empty_star empty_star 3 out of 5 stars

    Hub

    Should be standard equipment with the robotics wheels. It takes time to figure out exactly which Hub to order.

    RU from Nevis

  12. star star empty_star empty_star empty_star 2 out of 5 stars

    "Poor Concentricity"

    "We planned on using this to mount our drive sprocket specifically because of the claim it would help us align the sprocket; unfortunately, the concentricity of the bore and hub shaft is visibly off on all 4 pieces we ordered by a significant amount. This caused our sprocket to wobble (axially and radially) considerably, which isn't good for #25 chain. I suspect we got a bad batch, but I'd hope for better quality control."

    NC from Greenwood

  13. star star star star star 5 out of 5 stars

    Review

    These fit the 6" Mecanum Wheels much better than the old style hub.

    MG from Glendale

  14. star star star star star 5 out of 5 stars

    500EX hub.

    No problems. We are going to order some more.

    jw from tunbridge

Top of Page